T4G PENTIUM 4 OR CELERON SINGLE BOARD COMPUTER TECHNICAL INFO , TRENTON TECHNOLOGY SYSTEM HOST BOARD SINGLE BOARD COMPUTER

Transit Case and Rack System Integration

SINGLE BOARD COMPUTERS & ACTIVE / PASSIVE BACKPLANES

T4G (6130-xxx)
Jumpers Connectors Memory

T4G Reference Manual in PDF - click here.

6130tdb.gif
Jumpers
The setup of the configuration jumpers on the SBC is described below. * indicates the default value of each jumper.

NOTE:
For two-position jumpers (3-post), "TOP" is toward the memory sockets; "BOTTOM" is toward the edge fingers.

* = default value

JU6 THERMAL THROTTLING ACTIVITY LED
If the processor core gets to a critical temperature, it slows itself down to half its normal speed. This jumper sets the way in which the LED displays in response to this self-limiting mode.

Install for real-time activity. The LED lights only when the processor is operating in slow-power mode. *

Remove for latched activity. The LED lights and stays on once the processor has gone into slow-power mode.

JU8 PASSWORD CLEAR
Install for one power-up cycle to reset the password to the default (null password).
Remove for normal operation. *

JU10/JU11 SYSTEM FLASH ROM OPERATIONAL MODES
The Flash ROM has two programmable sections: the Boot Block for "flashing" in the BIOS and the Main Block for the executable BIOS and PnP parameters. Normally only the Main Block is updated when a new BIOS is flashed into the system.
JU10 JU11
All Blocks Write Enabled Remove * Remove *
Boot Block Write Protected Install Remove
Block 2-16 Write Protected Remove Install

JU12 CMOS CLEAR
Install on the TOP to operate. *
Install on the BOTTOM to clear.

NOTE: The CMOS Clear jumper works on power-up. To clear the CMOS, power down the system, install the jumper, then turn the power back on. Wait for at least two seconds and turn the power off. Then remove the jumper and turn the power on.
When AMIBIOS displays the "CMOS Settings Wrong" message, press F1 to go into the BIOS Setup Utility, where you may reenter your desired BIOS settings, load optimal defaults or load failsafe defaults.
Connectors
NOTE:
Pin 1 on the connectors is indicated by the square pad
on the PCB.

P3 - FLOPPY DRIVE CONNECTOR
34 pin dual row header, Amp #103308-7
PIN SIGNAL
1 Gnd
3 Gnd
5 Gnd
7 Gnd
9 Gnd
11 Gnd
13 Gnd
15 Gnd
17 Gnd
19 Gnd
21 Gnd
23 Gnd
25 Gnd
27 Gnd
29 Gnd
31 Gnd
33 Gnd
PIN SIGNAL
2 N-RPM
4 NC
6 D-Rate0
8 P-Index
10 N-Motoron 1
12 N-Drive Sel2
14 N-Drive Sel1
16 N-Motoron 2
18 N-Dir
20 N-Stop Step
22 N-Write Data
24 N-Write Gate
26 P-Track 0
28 P-Write Protect
30 N-Read Data
32 N-Side Select
34 Disk Chng

P4A - KEYBOARD HEADER
5 pin single row header, Amp #640456-5
PIN SIGNAL
1 Kbd Clock
2 Kbd Data
3 Key
4 Kbd Gnd
5 Kbd Power (+5V fused) with
self-resetting fuse

P5 - SPEAKER PORT CONNECTOR
4 pin single row header, Amp #640456-4
PIN SIGNAL
1 Speaker Data
2 Key
3 Gnd
4 +5V

P6 - SERIAL PORT 1 CONNECTOR
10 pin dual row header, Amp #103308-1
PIN SIGNAL
1 Carrier Detect
3 Receive Data-I
5 Transmit Data-0
7 Data Terminal Ready-0
9 Signal Gnd
PIN SIGNAL
2 Data Set Ready-I
4 Request to Send-O
6 Clear to Send-I
8 Ring Indicator-I
10 NC

P7 - SERIAL PORT 2 CONNECTOR
10 pin dual row header, Amp #103308-1
PIN SIGNAL
1 Carrier Detect
3 Receive Data-I
5 Transmit Data-0
7 Data Terminal Ready-0
9 Signal Gnd
PIN SIGNAL
2 Data Set Ready-I
4 Request to Send-O
6 Clear to Send-I
8 Ring Indicator-I
10 NC

P8 - PARALLEL PORT CONNECTOR
26 pin dual row header, Amp #103308-6
PIN SIGNAL
1 Strobe
3 Data Bit 0
5 Data Bit 1
7 Data Bit 2
9 Data Bit 3
11 Data Bit 4
13 Data Bit 5
15 Data Bit 6
17 Data Bit 7
19 ACK
21 Busy
23 Paper End
25 Slct
PIN SIGNAL
2 Auto Feed XT
4 Error
6 Init
8 Slct In
10 Gnd
12 Gnd
14 Gnd
16 Gnd
18 Gnd
20 Gnd
22 Gnd
24 Gnd
26 NC

P9 - PS/2 MOUSE AND KEYBOARD CONNECTOR
6 pin mini DIN, Kycon #KMDG-6S-B4T
PIN SIGNAL
1 Ms Data
2 Kbd Data
3 Gnd
4 Power (+5V fused) with
self-resetting fuse
5 Ms Clock
6 Kbd Clock

P9A - PS/2 MOUSE HEADER
6 pin single row header, Amp #640456-6
PIN SIGNAL
1 Ms Data
2 Reserved
3 Gnd
4 Power (+5V fused) with
self-resetting fuse
5 Ms Clock
6 Reserved

P10 - EXTERNAL RESET CONNECTOR
2 pin single row header, Amp #640456-2
PIN SIGNAL
1 External Reset In (Low Active)
2 Gnd

P11 - PRIMARY IDE HARD DRIVE CONNECTOR
 40 pin dual row header, 3M #30340-6002HB
PIN SIGNAL
1 Reset
3 Data 7
5 Data 6
7 Data 5
9 Data 4
11 Data 3
13 Data 2
15 Data 1
17 Data 0
19 Gnd
21 DRQ 0
23 IOW
25 IOR
27 IORDY
29 DACK 0
31 IRQ 14
33 Add 1
35 Add 0
37 CS 1P
39 IDEACTP
PIN SIGNAL
2 Gnd
4 Data 8
6 Data 9
8 Data 10
10 Data 11
12 Data 12
14 Data 13
16 Data 14
18 Data 15
20 NC
22 Gnd
24 Gnd
26 Gnd
28 SELPDP
30 Gnd
32 NC
34 PCBL DET *
36 Add 2
38 CS 3P
40 Gnd


* For ATA/66 and ATA/100 drives, which should be set for Cable Select for proper speed operation. If other Drives are detected, pin definition is Gnd.

P11A - SECONDARY IDE HARD DRIVE CONNECTOR
40 pin dual row header, 3M #30340-6002HB
PIN SIGNAL
1 Reset
3 Data 7
5 Data 6
7 Data 5
9 Data 4
11 Data 3
13 Data 2
15 Data 1
17 Data 0
19 Gnd
21 DRQ 1
23 IOW
25 IOR
27 IORDY
29 DACK 1
31 IRQ15
33 Add 1
35 Add 0
37 CS 1S
39 IDEACTS
PIN SIGNAL
2 Gnd
4 Data 8
6 Data 9
8 Data 10
10 Data 11
12 Data 12
14 Data 13
16 Data 14
18 Data 15
20 NC
22 Gnd
24 Gnd
26 Gnd
28 SELPDS
30 Gnd
32 NC
34 SCBL DET *
36 Add 2
38 CS 3S
40 Gnd

* For ATA/66 and ATA/100 drives, which should be set for Cable Select for proper speed operation. If other drives are detected, pin definition is Gnd.

P12 - HARD DRIVE LED CONNECTOR
4 pin single row header, Amp #640456-4
PIN SIGNAL
1 LED +
2 LED -
3 LED -
4 LED +

P15 - VIDEO INTERFACE CONNECTOR
15 pin HD15 connector, Amp #1-1470250-3
PIN SIGNAL
1 Red
2 Green
3 Blue
4 NC
5 Gnd
PIN SIGNAL
6 Gnd
7 Gnd
8 Gnd
9 +5V
10 Gnd
PIN SIGNAL
11 NC
12 EEDI
13 HSYNC
14 VSYNC
15 EECS

P16 - 10/100BASE-T ETHERNET CONNECTOR
8 pin shielded RJ-45 connector, Pulse #J0035D21B
PIN SIGNAL
1 TD+
2 TD-
3 RX+
4 NC
PIN SIGNAL
5 NC
6 RX-
7 NC
8 NC

P17A - UNIVERSAL SERIAL BUS (USB) CONNECTOR
4 USB vertical connector, Molex #67329-0000
(+5V over current protection)
PIN SIGNAL
1 +5V - USB0
2 USB0-
3 USB0+
4 Gnd - USB0

P17B - UNIVERSAL SERIAL BUS (USB) CONNECTOR
4 USB vertical connector, Molex #67329-0000
(+5V over current protection)
PIN SIGNAL
1 +5V - USB1
2 USB1-
3 USB1+
4 Gnd - USB1

P18 - SYSTEM HARDWARE MONITOR CONNECTOR
4 pin single row header, Amp #640456-4
PIN SIGNAL
1 Gnd
2 GPO (General Purpose Output)
3 CI (Chassis Intrusion Input)
4 OVT (Over Temperature)

P19 - CPU FAN
3 pin single row header, Molex #22-23-2031
PIN SIGNAL
1 Gnd
2 +12V
3 FanTach

P21 - POWER GOOD LED
2 pin single row header, Amp #640456-2
PIN SIGNAL
1 LED -
2 LED +

P22 - SYSTEM MANAGEMENT BUS CONNECTOR
2 pin single row header, Amp #640456-2
PIN SIGNAL
1 SMB Clock
2 SMB Data

P23 - +5V VRM SUPPLY
2 pin header, Molex #39-29-3026
PIN SIGNAL
1 +5V
2 +5V

P24 - +12V VRM POWER INPUT
4 pin header, Molex #39-29-3046
PIN SIGNAL
1 Gnd
2 Gnd
3 +12V
4 +12V

Memory
The Double Data Rate (DDR) memory interface consists of a single channel which terminates in two dual-in-line memory module (DIMM) sockets and supports auto detection of up to 2GB of memory. The System BIOS automatically detects memory type, size and speed.

The SBC uses industry standard 64-bit wide gold finger PC1600 or PC2100 memory modules in 184-pin DIMM sockets.

NOTE: Memory modules can be installed in one or both DIMM sockets. If only one DIMM module is used, it should be populated in the top DIMM socket (Bank 2 - Bk2). If two modules of different speeds are used, the 845GV chipset sets the memory interface speed to the speed of the slower DIMM module. Registered DIMMs are not supported. All memory modules must have gold contacts.

The SBC supports DIMMs which are PC1600/PC2100 compliant and have the following features:
  • 184-pin with gold-plated contacts
  • Non-ECC (64-bit) DDR memory
  • Unbuffered configuration
  • X8, x16 construction
  • Non-stacked (NS)

NOTE: Intel's DDR memory interface design guidelines for the 845GV chipset validate the use of non-stacked DIMM modules. Therefore, the T4G, which uses the 845GV chipset, supports only non-stacked DIMMs in its standard system BIOS.
DIMM Size DIMM Type Non-ECC Component
Construction
64 MB Unbuffered 8M x 64 x8, x16, NS
128 MB Unbuffered 16M x 64 x8, x16, NS
256 MB Unbuffered 32M x 64 x8, x16, NS
512 MB Unbuffered 64M x 64 x8, x16, NS
1 GB Unbuffered 128M x 64 x8, x16, NS
* Intel, Pentium and Celeron are registered trademarks of Intel Corporation.

All other product names are trademarks of their respective owners.

T4G Product Detail - Click Here
T4G Reference Manual - Click Here
SBC Support Page (drivers, etc.) - Click Here
   
 
Contact Us
Name :
Phone :
Email :
Company :
Comments :

  
Single Board Computers
Copyright © 2012 Chassis Plans
All Rights Reserved.
Home | About Us | Products |Support | Applications | Contact Us
CP Systems is a Division of Chassis Plans
Systems Engineered to Perform®
10123 Carroll Canyon Road - San Diego - CA - 92131 | tel: 858-571-4330 | fax: 858-571-6146 | e-mail: saleseng@chassisplans.com